Independent brewing lab — not affiliated with PourX, Abilliant or the domain's previous owner.
pourxlabthe pour-over lab

Guide · espresso

How to dial in espresso

Keep the dose fixed, choose a target yield (1:2, such as 18 g in and 36 g out, is the common start), then change only the grind until the shot reaches that yield in roughly 25–30 seconds. After that, taste decides: sour means extract more, bitter means extract less, and sour and bitter together point to uneven flow.

Updated 2026-11-17 · sources listed at the end · gram and ratio examples are our arithmetic from the sourced figures

Dialing in, step by step

  1. Fix the dose. Match it to the basket: Wikipedia’s Espresso article gives about 7, 14 and 21 g for single, double and triple baskets, and most baristas in the SCA’s 2017 survey dosed 18–20 g in an 18 g basket. Weigh every dose on a 0.1 g scale and leave it alone while you dial in.
  2. Set the yield. Multiply the dose by your ratio. The survey average was 1:2 (36.5 g out on average), with every answer between 1:1.5 and 1:2.5. Ratios and the ristretto–lungo names are covered in the espresso ratio guide.
  3. Prepare the puck the same way every time. Break up clumps, level the bed and tamp flat; Wikipedia notes that tamping “promotes the water's even penetration through the grounds.” Most surveyed baristas tamped at 20–30 lb.
  4. Pull, weigh, time. Stop at the target weight and note the seconds. Wikipedia gives 25–30 s as usual; the historic SCAA definition allowed 20–30 s.
  5. Adjust the grind by time. Finer grounds raise the bed’s resistance and lengthen the shot; coarser grounds shorten it (Smrke and colleagues, 2024). Move one grinder step at a time.
  6. Taste, then fine-tune the yield. Once the time is in range, use the chart below: a longer yield extracts more, a shorter yield less.
  7. Touch temperature and pressure last, if your machine lets you, and write every shot down.

Change one thing per shot. If dose, grind and yield all move together, the next shot cannot tell you which change mattered.

Espresso shot diagnosis chart

Read the time first, then the taste, with dose and yield where you set them.

Wide table — scroll sideways on a phone.

What you see and tasteLikely causeFirst change (only this one)Why
Runs fast (well under ~25 s) and tastes sour or thinUnder-extractedGrind one step finer; keep dose and yieldUnder-extraction is linked to a “predominantly sour” taste; finer grounds slow the flow and extract faster
Runs slow (well over ~30 s) and tastes bitter, harsh or dryingOver-extractedGrind one step coarserOver-extraction is linked to “predominant bitterness”; coarser grounds lower resistance
On time but still sourUnder-extractedLengthen the yield, e.g. 1:2 → 1:2.5 (18 g: 36 → 45 g)A longer brew gives a higher extraction yield
On time but still bitterOver-extractedShorten the yield, e.g. 1:2 → 1:1.5 (18 g: 36 → 27 g)Passing too much water through the puck can add unpleasant flavors
Sour and bitter at once, or weaker after grinding finerUneven flow (channeling)Do not grind finer; redo the puck prep. If it persists, go a step coarser or use a little less coffeeFine settings caused inhomogeneous flow and lower extraction (Cameron 2020); a cup can mix under- and over-extracted coffee (Lee 2023)
Same settings, shot times differ by more than 3 sInconsistent dose or prepCheck the dose to 0.1 g and repeat the same prep before judging tasteWBC rules require paired shots within 3.0 s; uneven flow is linked to poor reproducibility

The time window is a starting guide, not a rule; the WBC espresso definition sets no shot time at all. Smrke, Eiermann and Yeretzian found their taster preferred shots near 30 s for the coffee they tested, and say other coffees and roasts shift that point. The University of Oregon’s summary of Cameron and colleagues’ 2020 work describes the opposite approach: about 15 g instead of 20 g, ground coarser, in shots of 7 to 14 seconds. Whatever window you use, keep it fixed while you dial in one coffee.

Espresso shot time windows and which way the grind moves the shot A time axis from 0 to 45 seconds. A band from 7 to 14 seconds marks the faster, coarser shots described by the University of Oregon. A band from 20 to 30 seconds marks the historic SCAA definition and a darker band from 25 to 30 seconds the usual time given by Wikipedia and the 2017 barista survey. An arrow pointing right says grind finer to slow the shot; an arrow pointing left says grind coarser to speed it up. Numbered markers 1 to 5 match the list below. 051015202530354045 s 7–14 s 20–30 s 25–30 grind finer = slower shotgrind coarser = faster shot 1 2 3 4 5
  1. 7–14 s — the faster shots in the University of Oregon summary: about 15 g of coffee, ground coarser.
  2. 20–30 s — the historic SCAA espresso definition.
  3. 25–30 s — “usually” in Wikipedia’s Espresso article; half of the 2017 survey’s baristas averaged here.
  4. Grind finer — more resistance in the bed, so the same yield takes longer.
  5. Grind coarser — less resistance, so the shot runs faster.
Drawn by pourxlab.com for this page from the time ranges in Wikipedia’s Espresso article, SCA 25 Magazine and the University of Oregon summary, and the grind–flow findings of Smrke et al. 2024. Time axis to scale; arrows are directions only.

Shot checker

Ratio1:2
Flow1.3 g/s
Time vs 25–30 sin range

ratio = yield ÷ dose → 36 ÷ 18 = 2 · flow = yield ÷ time → 36 ÷ 28 = 1.3 g/s

Next: keep these settings and write the shot down.

The checker applies the chart above to your numbers, using Wikipedia’s usual 25–30 s window.

Channeling: when grinding finer makes it worse

Channeling is water following the path of least resistance through the puck, which extracts it unevenly (as the 2026 AIP release on the Warsaw study puts it). Wikipedia’s Coffee extraction article notes that in espresso “water can saturate the column unevenly from bottom to top.” In their 2020 Matter paper, Cameron, Hendon, Foster and colleagues found that extraction yield peaked at an intermediate grind and fell at finer settings, which they attributed to inhomogeneous flow — the cause of poor reproducibility and wasted coffee. The ZHAW group (Smrke et al., 2024) likewise reports that a grind that is too fine can extract unevenly and lower the yield.

A University of Huddersfield model (Lee, Smith and Arshad, Physics of Fluids, 2023) explains why it snowballs: more flow leads to more extraction, which lowers resistance and leads to more flow. Even when the overall extraction looks right, the cup can be a mix of underdeveloped and bitter coffee. That is the practical sign: a shot that tastes sour and bitter at once, or weaker after you grind finer, needs a more even puck, not a finer grind. As Hendon summed up the 2020 work: “the most reproducible thing you can do is use less coffee.”

For puck preparation, the University of Warsaw team behind a 2026 Physics of Fluids study shook the grounds, stirred them with a needle tool (the Weiss distribution technique, WDT) and then tamped at 20 kg on an 18.50 g dose.

What pressure does

Espresso is brewed at about 9 bar almost everywhere you look: 9–10 atm in the historic SCAA definition, 9 ± 1 bar for the Italian institute’s certified espresso (via Wikipedia), 8.5–9.5 bar in the 2026 World Barista Championship rules, and 9 bar as the most common answer (8.5 bar average) in the 2017 survey. A University of Navarra study that pulled arabica espresso at 7, 9 and 11 atm (Andueza et al., 2002) found that the 11 atm shots stood apart on foam and taste, and that the 9 atm shots had more consistent foam and more of the odorants linked to fresh, fruity, malty and buttery notes.

More pressure does not simply mean a faster shot. The Warsaw study brewed 60 coffees at 11 basket pressures from about 1 to 12 bar: flow rose in step with pressure below about 5 bar, then leveled off in the usual brewing range, which the authors trace to the puck compacting under load. On most home machines the pump pressure is not something you adjust shot to shot, so grind remains the control for time. About half the surveyed baristas (52%) also used pre-infusion.

What temperature does

Published ranges are narrow: 195–205 °F (90.5–96.1 °C) in the historic SCAA definition, 90.5–96 °C in the 2026 WBC rules, and a 200.3 °F average in the survey. Andueza and colleagues (2003) tested 88, 92, 96 and 98 °C and chose 92 °C for arabica; notably, taste and mouthfeel measurements were “not very useful” for choosing the temperature — aroma compounds and flavor profiles decided it. Leave temperature at a setting inside the published range until grind and yield are settled, and change it in small steps if at all.

Dose matters too, but it is the variable to hold still. In a related Navarra study (Andueza et al., 2007), raising the dose from 6.5 to 8.5 g per 40 ml increased foam, and caffeine and bitterness rose with dose in some blends.

Dial-in log

Copy this table, or use the printable brew log template (it has an Espresso method).

#Dose gYield gTime sRatioGrindTasteNext change
1
2
3

For espresso the extraction yield is generally 15–25% (Wikipedia, Coffee extraction); if you own a refractometer, the extraction yield calculator turns a TDS reading, dose and yield into that number. Grind-size background is in the grind size chart and coffee grinders explained.

Sources

  1. Wikipedia — Espresso (secondary: usually 25–30 s; baskets of about 7, 14 and 21 g; tamping “promotes the water's even penetration”; certified Italian espresso 9 ± 1 bar, 88 ± 2 °C at exit; Faema E61 electric pump at 9 bar)
  2. Wikipedia — Coffee extraction (secondary: under-extraction “predominantly sour”, over-extraction “predominant bitterness”; finer grind extracts faster; longer brewing time gives higher yield; water can saturate the espresso column unevenly)
  3. Fasman D. — Defining the Ever-Changing Espresso. SCA 25 Magazine, Issue 3 (historic SCAA definition: 7–9 g single / 14–18 g double, 20–30 s, 195–205 °F, 9–10 atm; 2017 survey of 275 baristas: 18–20 g, 36.5 g average yield, 1:2, 25–30 s, 8.5 bar average with 9 most common, 52% pre-infuse, 200.3 °F average, 20–30 lb tamp)
  4. World Coffee Championships — 2026 World Barista Championship Official Rules and Regulations (§3.1E dose not fixed; §3.1F 90.5–96 °C; §3.1G 8.5–9.5 bar; §3.1H pairs within 3.0 s)
  5. Cameron M.I., Morisco D., Hofstetter D., Uman E., Wilkinson J., Kennedy Z.C., Fontenot S.A., Lee W.T., Hendon C.H., Foster J. (2020) Systematically improving espresso: insights from mathematical modeling and experiment. Matter. doi:10.1016/j.matt.2019.12.019 (extraction yield peaks at an intermediate grind; inhomogeneous flow at fine settings, poor reproducibility)
  6. University of Oregon — UO chemist helps find path to consistently good espresso (January 22, 2020: 15 g instead of 20 g, coarser grind, 7–14 s; “the most reproducible thing you can do is use less coffee”)
  7. Smrke S., Eiermann A., Yeretzian C. (2024) The role of fines in espresso extraction dynamics. Scientific Reports 14:5612 (20 g in, 40 g out at 9 bar; fines under 100 µm lower permeability and lengthen extraction; finer grind, larger pressure drop; preferred flavor near 30 s for the coffee tested)
  8. EurekAlert! / AIP Publishing — news release on Lee W.T., Smith A., Arshad A. (2023) Uneven extraction in coffee brewing. Physics of Fluids 35:054110, University of Huddersfield (two-region model; flow–extraction feedback; a cup can mix under- and over-extracted coffee)
  9. Waszkiewicz R., Myck F., Białas Ł., Puciata-Mroczynska M., Dzikowski M., Szymczak P., Lisicki M. — Under pressure: poroelastic regulation of flow in espresso brewing (arXiv 2512.21528; published in Physics of Fluids, June 2026): linear flow below about 5 bar, saturation in the brewing regime; 18.50 g dose, needle distribution, 20 kg tamp
  10. EurekAlert! / AIP Publishing — It's hard to espresso how pressure affects brewing (June 23, 2026; University of Warsaw; espresso usually brewed at about 6 to 9 atmospheres; more pressure no longer raises flow)
  11. Innovations Report — Study of espresso coffee quality (February 12, 2004: University of Navarra doctoral thesis by Susana Andueza; 88–98 °C and 7, 9, 11 atm tested; 92 °C and 9 atm selected)
  12. Andueza S., Maeztu L., Dean B., de Peña M.P., Bello J., Cid C. (2002) Influence of water pressure on the final quality of arabica espresso coffee: application of multivariate analysis. J. Agric. Food Chem. 50:7426–7431 (abstract record: 7, 9, 11 atm; 9 atm more consistent foam and more fresh, fruity, malty and buttery odorants)
  13. Andueza S., Maeztu L., Pascual L., Ibáñez C., de Peña M.P., Cid C. (2003) Influence of extraction temperature on the final quality of espresso coffee. J. Sci. Food Agric. 83:240–248, doi:10.1002/jsfa.1304 (abstract record: 88, 92, 96, 98 °C; 92 °C best for arabica; taste and mouthfeel “not very useful” for choosing temperature)
  14. Andueza S., Vila M.A., de Peña M.P., Cid C. (2007) Influence of coffee/water ratio on the final quality of espresso coffee. J. Sci. Food Agric. 87(4):586–592 (6.5, 7.5, 8.5 g per 40 ml at 92 °C, 9 atm, 21 ± 3 s; foam rose with dose; caffeine and bitterness rose with dose in some blends)